страниц 36
язык английский
Содержание
Scania EMS Инструменты
Приборная панель (аналог)
Поиск и устранение неисправностей с помощью флэш-кодов для блока управления EMS
Обзор флэш-кодов для блока управления EMS
Поиск и устранение неисправностей с помощью флэш-коды для координатора EMS
Обзор флэш-кодов для координатора EMS
Панель Scania управления (SCP)
Пульт дистанционного управления Box (RCB)
Scania EMS Дисплей (СЕГ)
Информация на экране
Коды неисправностей
Настройки
Сигнализация и генерации кода неисправности
1. Блок управления S6
2. Главная блок Supply Box
3. Контролер
4. Координатор
5. Координатор Соединительная коробка (мастер)
6. Координатор Соединительная коробка (ведомый)
7. Панель управления (мастер)
8. Панель управления (ведомый)
9. Панель приборов
10. Scania EMS Дисплей
11. Датчик положения
12. Пульт дистанционного управления Box
Scania приборы, двойная система
ФЛЕШЬ (БЛИНК) КОДЫ НЕИСПРАВНОСТИ-язык английский
Overview of flash codes for EMS control unit
Code Description Code Description
0 No fault detected. 53 PDE in cylinder 3: The solenoid valve does not
work correctly.
11 Over-revving. One or both engine speed
sensors shows a speed in excess of 3,000 rpm. 54 PDE in cylinder 4: The solenoid valve does not
work correctly.
12 Engine speed sensor 1 faulty, or incorrect
signal. 55 PDE in cylinder 5: The solenoid valve does not
work correctly.
13 Engine speed sensor 2 faulty, or incorrect
signal. 56 PDE in cylinder 6: The solenoid valve does not
work correctly.
14 Coolant temperature sensor faulty, or incorrect
signal. 57 PDE in cylinder 7: The solenoid valve does not
work correctly.
15 Charge air temperature sensor faulty, or
incorrect signal. 58 PDE in cylinder 8: The solenoid valve does not
work correctly.
16 Charge air pressure sensor faulty, or incorrect
signal. 59 Incorrect signal in extra analogue input.
17 Oil temperature sensor faulty, or incorrect
signal. 61 Incorrect control unit shutdown.
18 Oil pressure sensor faulty, or incorrect signal. 66 Shutdown due to coolant level.
21 Coolant level sensor faulty. 68 Alternator charging incorrectly.
23 Internal fault code in the coordinator. 69 Starter motor function interrupted or not
activated.
24 Accelerator/brake. If the accelerator and brake
pedals have been operated simultaneously. 82 Engine speed above ref. engine speed at start.
25
Accelerator sensor/idle switch.
Accelerator sensor/kickdown switch.
Fault in memory circuit (EEPROM) in control
unit.
27 Engine shutdown bypassed. 84 Data transfer to the control unit memory
(EEPROM) has been interrupted.
28 Shutdown due to oil pressure. 85 Incorrect internal temperature in the control
unit.
31 Torque limitation due to oil pressure. 86 Internal fault in the control unit: Fault in
hardware control.
32 Incorrect parameters for limp home function. 87 Fault in control unit RAM.
33 Battery voltage incorrect or no signal. 88 Internal control unit fault: Memory fault.
37
Emergency shutdown switch activated in
accordance with CAN message from
coordinator.
Incorrect seal: Prohibited changes in software.
43 CAN circuit faulty in the control unit. 93 Engine speed sensors faulty or not connected.
